Nexug Industries Private Limited

The Phyton 168ES bevelling system is developed as a portable device for cutting pipes and tubes and for preparing welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portions for machining tubes with wall thicknesses up to 80mm (3.14").
Phyton 168ES is the outside clamping machine. One half of the ring is clamped on the tube to be machined, while the other, rotating half of the ring carries two tool holders equipped with automatic feed. The automatic feed makes machining thick-walled tubes highly productive and comfortable.
The machine can be used only for cutting the pipe, or when using a bevelling tool, for simultaneous cutting and bevelling of the pipe in single working cycle.
The Phyton 168ES can be deployed directly from the pipe face, or it can be split into two halves and reassembled around the pipe. This feature is especially useful for bevelling or cutting of continuous pipelines systems, such as those found in chemical plants, power stations, or excavation sites.

• Bevel operations including J-bevel.
• Pipe face alignment operation. Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Automatic feeding of cutting tools.
• Possibility to split the frame ring for mounting on continuous piping systems.
• Possibility of pneumatic drive.
• Possibility to customise the cutting tools according to specific requirements on request.

The Phyton 89ES bevelling system is developed as a portable device for cutting pipes and tubes and for preparing welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portions for machining tubes with wall thicknesses up to 80mm (3.14").
Phyton 89ES is the outside clamping machine. One half of the ring is clamped on the tube to be machined, while the other, rotating half of the ring carries two tool holders equipped with automatic feed. The automatic feed makes machining thick-walled tubes highly productive and comfortable.
The machine can be used only for cutting the pipe, or when using a bevelling tool, for simultaneous cutting and bevelling of the pipe in single working cycle.
The Phyton 89ES can be deployed directly from the pipe face, or it can be split into two halves and reassembled around the pipe. This feature is especially useful for bevelling or cutting of continuous pipelines systems, such as those found in chemical plants, power stations, or excavation sites.

• Bevel operations including J-bevel.
• Pipe face alignment operation. Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Automatic feeding of cutting tools.
• Possibility to split the frame ring for mounting on continuous piping systems.
• Possibility of pneumatic drive.
• Possibility to customise the cutting tools according to specific requirements on request.

The beveling system C-Biter 114E is developed as a portable device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and a generous power portion for machining tubes with wall thicknesses up to 12mm (.47").
C-Biter 114E is a machine with external pipe clamping. The clamping and self-centering of the machine is provided by unique clamping jaws, outside of the tube. The automatic feed makes machining highly productive and comfortable.
The machine can be used for bevelling pipes, but also for machining solid bars.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Automatic machine feed.
• Possibility of processing solid bars.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.
• Possibility to supply clamping jaws for the non-standard pipe diameter.

The beveling system C-Biter 76E is developed as a portable device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and a generous power portion for machining tubes with wall thicknesses up to 12mm (.47").
C-Biter 76E is a machine with external pipe clamping. The clamping and self-centering of the machine is provided by unique clamping jaws, outside of the tube. The automatic feed makes machining highly productive and comfortable.
The machine can be used for bevelling pipes, but also for machining solid bars.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Automatic machine feed.
• Possibility of processing solid bars.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.
• Possibility to supply clamping jaws for the non-standard pipe diameter.

The Stinger 830E bevelling system is developed as a portable self-centering device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portion for performing up to three operations in a single step.
The Stinger 830E allows you to perform several operations (some in a single step) such as aligning the end and edge of the pipe, bevelling, or calibrating the inner diameter of the pipe to be machined.
Of course, it is also possible to actively perform only one of the above operations separately.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Multiple operations in a single step.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.

The Stinger 240E bevelling system is developed as a portable self-centering device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portion for performing up to three operations in a single step.
The Stinger 240E allows you to perform several operations (some in a single step) such as aligning the end and edge of the pipe, bevelling, or calibrating the inner diameter of the pipe to be machined.
Of course, it is also possible to actively perform only one of the above operations separately.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Multiple operations in a single step.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.

The Stinger 426E bevelling system is developed as a portable self-centering device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portion for performing up to three operations in a single step.
The Stinger 426E allows you to perform several operations (some in a single step) such as aligning the end and edge of the pipe, bevelling, or calibrating the inner diameter of the pipe to be machined.
Of course, it is also possible to actively perform only one of the above operations separately.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Multiple operations in a single step.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.

The Stinger 300 pipe beveling machine is designed for portable use in pipe machining operations and it can be used efficiently by a single operator. The Stinger 300 is a heavy-duty ID mounted pipe beveler utilizing self-centering expandable mandrels to provide quick and proper alignment to a pipe or a tube prior to machining operations.
The Stinger 300 can bevel, face and counter-bore in a single operation, making all these weld prep operations quick and simple.
EasyLOCK - The tool bit is fastened by one screw anywhere on the holder. The holder is equipped with a scale for easier tool’s centering.
The Stinger 300 can be used with three or two tool’s holders only depending on the required bevelling job.

• Simultaneous bevel, face, and counter-bore

• EasyLOCK - locking of the tool bit by one screw
• Centering scale

• Standard or custom-made tool bits
• J-Bevel tool bits available for high welding efficiency on thicker walled pipe

• Centering screw to eliminate the potential vibrations.

The Stinger 76E bevelling system is developed as a portable self-centering device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and generous power portion for performing up to three operations in a single step.
The Stinger 76E allows you to perform several operations (some in a single step) such as aligning the end and edge of the pipe, bevelling, or calibrating the inner diameter of the pipe to be machined.
Of course, it is also possible to actively perform only one of the above operations separately.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Operation of alignment and calibration of the inner diameter of the pipe.
• Multiple operations in a single step.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.

The beveling system C-Biter 63E is developed as a portable device for the preparation of welding surfaces on pipes and tubes. It is preferred for an easy operation, reliability and a generous power portion for machining tubes with wall thicknesses up to 12mm (.47").
C-Biter 63E is a machine with external pipe clamping. The clamping and self-centering of the machine is provided by unique clamping jaws, outside of the tube. The automatic feed makes machining highly productive and comfortable.
The machine can be used for bevelling pipes, but also for machining solid bars.

• Bevel operations including J-bevel.
• Pipe face alignment operation - Facing.
• Automatic machine feed.
• Possibility of processing solid bars.
• Possibility of pneumatic drive.
• Possibility to customise cutting tools according to specific requirements on request.
• Possibility to supply clamping jaws for the non-standard pipe diameter.

Pipe bevelling system with inner clamping, automatic feeding:

• Robust portable pipe bevellers with automatic feeding.
• The machines are designed to straighten the front, create bevel and inner calibration of pipe diameter.
• The angle and shape of bevel is optional. When adjusted, the machine is able to get the ends of pipes rapidly and repeatedly ready for welding.
• Concentric inner clamping is the guarantee of perfect securing and centring of the machine.
• Clamping in pipe axis can be an advantage in specifically confined conditions.
• Option to select electric or pneumatic drive.

Pipe bevelling system with outer clamping, suitable for operations on membrane walls or confined areas:

• Robust portable pipe bevellers with dia. range from Ø 8 – 108mm.
• The machines are designed for operations in confined areas, or for operations on membrane walls.
• The angle and the shape of bevel are optional. When adjusted, machines are able to get the ends of pipes rapidly and repeatedly ready for welding.
• Useful to all machinable metals, including stainless steels.
• Option to select electric or pneumatic drive.

 

Electric machine versions:

• The machine is fitted with high performance electromotor in a metal chassis with enhanced resistance.